There have previously been very few studies of forests on Seram Island in the Eastern Indonesian archipelago and none before on lowland limestone primary forests. The COLUPSIA project on collaborative land use planning has therefore chosen Seram as one of two project sites. The objective of the COLUPSIA project is to establish collaborative and equitable land use planning. In order to achieve its objective the COLUPSIA project aims to improve understanding of traditional resource management and how it interacts with governmental systems, as well as enhancing knowledge about tropical landscapes and ecosystem services.The aim of this study was to contribute to the COLUPSIA project through describing lowland limestone forest on Seram Island in respect to (1) forest structure, (2) tree species richness and (3) tree species composition. We set up 5 plots, each of 0.2 ha, at one site, Mawalai, and collected data on tree variables (tree diameter ?10 cm) as well as for some other life forms and environmental data.

Abstract This thesis is based on a case study of the drawn out legal process on the question of establish a limestone quarry in Bunge Ducker in north Gotland (Sweden). The current fields are located next to areas that are protected by virtue of being EU-certified Natura 2000-areas. Despite this, the Swedish governments and courts have not agreed in witch national interest that should be prevail when decisions are made on this issue. This phenomenon are reflected in the judicial process and different court have evaluate information differently in the case. A change among governmental actors where priority is given to the importance of national interest have occur in the later part in the process.

An excessive input of nutrients to lakes and other water bodies has created a problem with eutrophication in Sweden. Untreated, or partially treated, domestic sewage is a major source for discharge of phosphorus (P), which is the nutrient most frequently responsible for eutrophication of most fresh waters and the Baltic Sea. The waste water can be cleaned by filter materials, which have a high P-retention ability and which after saturation may be used as fertilizers. Four potentially suitable filter materials were tested in batch- and column experiments in this study. In the batch experiments, the following materials were shaken with waste water in time series ranging from 5 seconds to 60 minutes: coarse (1-4 mm) and fine (0-2 mm) Polonite® (heated bedrock from Poland); Filtralite® (light expanded clay aggregates with limestone added before burning); water cooled blast furnace slag (BF-slag) and BF-slag mixed with 10% burned limestone.

This study aims to assess the normal inflow of extraterrestrial chromite to Earth. The results from the investigationare compared to earlier studies of middle Ordovician Orthoceratite Limestone in which 1 - 3 extraterrestrial chromitegrains ( >63 ?Êm ) per kilogram limestone were found. These values have been interpreted as evidence of a twoorders of magnitude increase in the flux of extraterrestrial matter to Earth during a part of middle Ordovician.From an early Paleocene marine sedimentary sequence with known sedimentation rate in Zumaia, northernSpain, 90,5 kilogram of condensed limestone, dated to about 63 Ma, was sampled. The limestone was dissolved inhydrochloric- and hydrofluoric acid and the residue was sieved and searched for opaque minerals under the binocularmicroscope.

One of the most common ways to produce heat and electricity in Europe today is by the incineration of waste or combustion of coal. These materials can be very sulfurous and during combustion sulfur dioxide is produced. This is an environmental and health related toxic substance which is why power plants have strict regulations on removing it from the flue gas. Sulfur dioxide is removed from the flue gas by adding a limestone reagent. The sulfur dioxide reacts with the limestone and the synthetic product obtained is ?Flue Gas Desulfurization gypsum?.

A pavement construction designed to cope with the different type of traffic loads; it is exposed to and at the same time it can resist the effect of the climate. A road structure consists of sub- and superstructure which is divided by a boundary known as terrace. During the construction of unbound layers (base course and sub-base course) in the superstructure, it is always ensured that the material meet the requirements for bearing capacity and the degree of compaction. These parameters are controlled by various laboratory tests and control methods. To obtain increased knowledge of the material and improve the quality of the compaction in the field, it is necessary to perform laboratory tests in order to determine material properties.A base course material 0/ 32 mm limestone from Gotland (Hejdeby) was investigated in this study.

A well, situated on Listerlandet in the western part of Blekinge in Sweden, has a very high content of nitrate. Water with a too high content of nitrate is hazardous to human health, in particular to small children. The area surrounding the well is mostly drained agricultural land with some larger farms for chicken and mink. The well takes its water from the bedrock and is deeper than most other wells affected by nitrate. The bedrock in the area is dominated by limestone with a relatively high flow of water.This thesis was performed in order to find the source of the nitrate.

The use of gabions means a reduced amount of filling material in the road section and a more narrow construction. Also the use of limestone cement columns can be reduced. All together this results in lower costs. The columns stand for about 55% of the total costs for the road. If gabions are used you can reduce the total costs with over 10%..

Dagens företag och organisationer måste ständigt förändra och förnya sig för att kunna överleva. Många av de studier som genomförts, visar att implementeringar av strategiska beslut i företag och organisationer ofta misslyckas och implementerings-arbetet beskrivs av många forskare som en konst snarare än en vetenskap. Förändringsarbetet och i synnerhet implementeringsfasen är det som fokuseras i detta arbete. Det finns många olika orsaker till varför implementeringsarbeten misslyckas, men genomgående så lyfts den interna kommunikationen fram som en ytterst kritisk faktor. Detta är orsaken till att vi på djupet studerat detta ämnesområde.

Vid betongframställning förekommer det spridningar i delmaterialens egenskaper som påverkar den färskaoch hårdnande betongen. Spridningarna i betongens delmaterial har studerats hos tre av Skanskas betongfabriker(Göteborg, Luleå och Norrköping), genom provuttag som analyserats hos Cementa Research.Provuttag har gjorts en gång per månad under ett års tid från fabrikerna. Delmaterialen som har analyseratsär ballast, cement, flytmedel och kalkfiller (endast hos Göteborg och Norrköping). Siktning av ballast0-8 mm har utförts med den traditionella siktningen. För kornstorlekar mindre än 0,25 mm, cement samtkalkfiller har lasersiktning använts.För att få en överskådlig bild över spridningarna hos delmaterialen har en analys utförts som illusteraravvikelserna med exakta siffror.

This thesis has been developed inassociation with Strängbetong AB, Sweden.A few years backCementa AB introduced a new type of cement on the Swedish market: Byggcement,which is a Portland Limestone Cement. This type of cement is better for theenvironment and cheaper than Rapid Hardening Cement which is used today at SträngbetongAB.Strängbetong AB isvery interested in a change of cement in the factory and wants to know what ittakes to make a transition from Rapid Hardening Cement to Byggcement.This final projectaims at investigating how the workability and strength development are affectedby a transition from the existing cement to Byggcement and how we can change theproperties of the concrete by adding different types of superplasticizers. Laboratory and factoryexperiments were made, to investigate the transition..

This thesis has been developed inassociation with Strängbetong AB, Sweden.A few years backCementa AB introduced a new type of cement on the Swedish market: Byggcement,which is a Portland Limestone Cement. This type of cement is better for theenvironment and cheaper than Rapid Hardening Cement which is used today at SträngbetongAB.Strängbetong AB isvery interested in a change of cement in the factory and wants to know what ittakes to make a transition from Rapid Hardening Cement to Byggcement.This final projectaims at investigating how the workability and strength development are affectedby a transition from the existing cement to Byggcement and how we can change theproperties of the concrete by adding different types of superplasticizers. Laboratory and factoryexperiments were made, to investigate the transition..

This is a final year project considering constructional techniques for joining cavity walls. The project is related to an ongoing scientific programme about the restoration of The City wall of Visby located on Gotland. The programme was set by Riksantikvarieämbetet as a reaction to a collapse of the outer masonry wall shell which took place in February 2012.The City wall of Visby is a medieval fortification built out of limestone during the 13th century. The wall is constructed as a cavity wall with two separate masonry shells connected to each other through an intermediate core. During the 14th century the wall was heightened which lead to a higher stress, especially in the outer wall face.

Burnt Spine-cap Sárcodon fuligíneovioláceus are one the most endangered mycorrhizal fungal species in Europe. They have their main distribution in Sweden. It form mycorrhiza with pine and dependent on limestone, which makes it connected to a rare environment. It has therefore been important to study the ecology of it further and to recognise the requirement it has on the environment more accurate and what it need to establish in a new area. In this study, 31 of 34 known sites in Sweden was visited and studied in field and their history analysed through aerial photographs.

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.